For use in chemists shop and schools upto intermediate classes, designed and fabricated for rough handling.

Beam :	Brass beam with 100 notches graduated for rider use with zero at center
Arrestment :	Six-point arrestment. The beam is raised for working
Rider :	Single wire, easy operating arrangement
Knives and Planes :	Best quality agate
Pan :	Stainless steel concave inwards
Pan Diameter :	7. 5 cm
Capacity :	200 gm
Sensitivity :	0. 2 mg

A short-armed triangular type Beam Balance. It is very suitable for research work in universities and industrial laboratories, specially designed to maintain constant sensitivity under varying load and acute self- acting parallel arrestment of the beam.

Capacity :	200 gm
Sensitivity :	0. 1 mg
Pan Diameter :	7. 5 cm

A short beam highly sensitive, divide in graduation 0-1g for rider, extended sports movement on agates and bearings, two pan attached with hanger and two air damping system upon the pan. Dial of chain 0-100mg. Pillar mounted on wooden mica base, front and side doors, teakwood case. Three leveling screws for accurate level.
Capacity : 200 gms.
 Sensitivity : 0.1 mg.

Cast iron moulded body all working parts of tempered steel. Spray painted finish. Both sides removable steel pans with pointer in the centre. Useful for quick weighing of heavy articles.

A single pan low form balance with three tired beams which can weigh up to 2610 gm. when used with supplementary masses, the balance has three notched weighing beam with center indicating sliding masses giving total capacity of 610gm. Additional masses are hung on the Beam increasing the capacity up to 2610gm. And they can be stored in the recessed base when not required.

Magnetic damping :
Beams :	0 to 500g x 100gm. 0 to 100g x 10gm. 0 to 10g x 0.1gm.
Supplementary masses :	2 x 1000gm. 1 x 500gm.
Pan :	Stainless Steel (dia.150 mm.)

With single pan and captive weights sliding on scales. Reading can be taken with index scale and pointer.
Mounted on wooden base.

Scale Division :
On Rear Scale	0-1gm x 100 mg.
On Middle Scale	0-300 Gms.
On Front Scale	0-10gm x 1 gm.
Capacity :	311 gm.
Sensitivity :	2 mg.
Distance Hook to Pan :	170 mm.
Pan Diameter :	110 mm.

Two pan balance for accurate and rapid weighing up to 2kg, used with supplementary masses. With cast alloy base and features angled beams with center reading poises, magnetic damping, spring loaded zero adjust compensator, precision ground knives and cross braced aluminium alloy beam.
Equipped with facility for under balance weighing.
Beams : 0 to 200g x 10g  and  0 to 10 g x 0.1g
Pan : Stainless Steel Dia.150 mm.
 Accessory tare and rod optional

Platform type scale, calibrated 125x0.5 kg. with zero adjustment and magnifier over scale opening.
Accurate, sensitive and portable.

Plastic case slopping front detachable rigid plastic load pan. Krumbbled Zero adjustment control. Capacity: (a) 1Kg x 5g (b) 2Kg x 10g (c) 4Kg x 20g

Nickel-plated burner tube of brass 12 mm. diameter with air regulator adjustable and a cylindrical riffled, mounted on a painted metal base. Suitable for Natural gas. Brass tube 100 x 12 mm. Height x diameter. Base 70-mm. diameter.Overall height 145 mm.

Nickel-plated burner tube of brass 11mm. diameter with air regulator adjustable and a cylindrical riffed connector, mounted on a painted metal base. Suitable for Natural gas. Brass Tube 90 x 11 mm. height x diameter. Base 90-mm. diameter. Overall height 130 mm.

Chrome plated brass tube with air regulator. Designed to give very high temperature. Overall height 15cms. and base dia. 8cms. approx.

Nickel plated burner tube of brass fitted with Steel/Ceramic grid 22 mm. diameter to give a high and evenly distributed flame temperature. Painted metal base.

To fit onto Bunsen burner so as to provide wide flame for bending glass tubing.

Hemispherical, made from thick copper sheet, with two handles and a set of concentric rings.

	Diameter (mm)
a.	100
b.	125
c.	150
d.	200

Hemispherical, made of thick aluminium sheet, with two handles and a set of concentric rings.

	Diameter (mm)
a.	100
b.	125
c.	150
d.	200

Cylindrical, made from thick aluminim sheet, with two handles and a set of concentric rings.

	Diameter (mm)
a.	125
b.	150
c.	200

With built- in Electric heating circular water bath. Anodized aluminium, 200mm diameter 125mm deep, with integral constant level device, set of aluminium rings, plastic feet and 1KW heater with overheat protection device. With connector and 3- core cable. For 220-240Volt AC supplies. Spare heating element 1KV for above available at extra cost.

Porcelain, flat form, glazed inside and outside, with spout.

	A	B	C	D	E	F
Outer Dia (mm)	60	75	100	125	150	175
Height (mm)	25	50	100	260	380	600

Porcelain, shallow form, glazed inside and outside, with spout.< /tr>

	A	B	C	D	E	F	G	H	I
Outer Dia (mm)	25	40	50	60	75	85	100	110	125
C apacity (ml)	8	15	20	40	100	125	175	275	450

Porcelain, Squat type, glazed inside and outside, complete with lid having ringed handle.Capacity (ml)

	A	B	C	D	E	F	G	H
15	25	30	50	80	100	150	200

Porcelain, Tall form. Glazed inside and outside, Complete with lid having ringed handle.

	A	B	C	D	E	F	G
Capacity (ml)	10	20	25	30	35	50	100

Low form, glazed inside and outside, translucent.

	Capacity (ml)
a.	15
b.	25
c.	50
d.< /td>	80
e.	150

Also available nickel and platinum crucibles of different capacities /Sizes.

Porcelain glazed outside and without lid.

	Capacity (ml)
a.	15
b.	20
c.	25
d.< /td>	30
e.	50
f.	100

Nickel Crucibles, 0.5mm thick.

Capacity (ml)	Dia. (mm)	Lid Dia. (mm)
10	25	25
15	30	30
25	35	35
30	40	40

Made of soda glass.

	a	b	c	d	e	f
Height (cms)	10	10	10	12.5	12.5	15
Diameter (cms)	15	20	25	25	30	30

Made of porcelain, for pneumatic trough, glazed inside and out.

	a	b	c	d
Capacity (ml)	6	7.5	8.5	10

Made of Borosillicate glass.

	a	b
Capacity (ml)	250	500

Glass, with 2 necks.

	a	b
Capacity (ml)	250	500

Made of soda glass, complete with delivery tube, thistle funnel and rubber cork.

	a	b	c	d
Capacity (ml)	250	500	750	1000

Made of Borosillicate glass. A rapid and effective apparatus to produce controllable amounts of common gases such as hydrogen sulphide, carbon dioxide etc. It is quickly changed and assembled, simple to operate.

	a	b	c
Capacity (ml)	250	500	1000

Steel cup & rod held by cork, al.  cap, length 35cm,  cap dia 90mm,  cup 18mm.

Heavy gauge stainless steel wire, for use in test tubes 150 x 25mm. Shaft shaped to prevent contact with wall. Length 20 cm. and diameter of cup 18 mm.

Made of G.I. wire, asbestos centre, extra strong quality. In squares, pack of 10 pcs.
Sides : a) 12.5 cms and (b) 15 cms

Made of Steel wire, ceramic center, extra strong quality, in squares, pack of 10 pcs.
Size : (a) 12.5 cms  and (b) 15 cms

Clay pipe on thick iron wire.
Size (cms) : (a) 5  (b) 6 (c) 7.5

With metal wick holder and glass stopper, superior quality.
Capacity (ml) : (a) 60 and (b) 125

Polyhedral, heavy duty allows the position of flame at just the right angle for each task, complete with cap and one wick.

Metallic Sheet die pressed, with woven wick in metal holder, screw on cap. Capacity 100 m.
Metal :
(a) Aluminium
(b) Brass
(c) Stainless Steel

Porcelain, good quality, unglazed inside, glazed outside.

	a	b	c	d	e	f	g
Sides (cms) :	7.5	10	12.5	15	17.5	20	25

Made of porcelain

	a	b
Depressions	6	12

Porcelain, glazed
Shape : (a) Round (b) Oval

The siphons are self- priming. Container may be emptied inserting the open end of the tube in the liquid and pumping the bulb with stopcock closed. As soon as the liquid enters the bulb, the flow is automatically regulated. No further pumping is needed and the stopcock may be used to dispense whenever required.
Size (mm) : (a) 6 and (b) 12.5

Completely stable and free form rocking movements. Box type. Load platform size 14 x 12.5 cms. Closed height 7 cms. Open height 22.5 cms. Maximum load capacity 5 kgs.

Cast iron top and mild steel legs. Finished in hammer/black color and legs are bent outwards for stability.

	Height (cms)	Length of Side (cms)
a.	20	12.5
b.	20	15

Top triangular, Stainless steel, length of one side 13 cms. and height 20 cms.

Complete with rod, cast iron base, painted in blue / black color and with hole. Iron rod 12.5 mm diameter nickel-plated. One end of rod is rounded and the other end is machine threaded with washer and hexagonal nut. Rod Length (cms) 20, 15, 75

Complete with rod, cast iron base, painted in blue/black color and with hole. Iron rod 12.5 mm diameter nickel-plated.
One end of rod is rounded and the other end is machine threaded with washer and hexagonal nut.

	a	b	c	d
Base Size (cms)	16 x 10	20 x 12.5	25 x 15	31.5 x 20
Rod Length (cms)	50	60	75	100
Base Weight (kgs) approx.	0.75	1.25	2.03	3

Complete with rod, base made of mild steel plate with hammer black powder coated finish and hole. Iron rod 12.5 mm diameter nickel-plated provided with locked pin for extra tightening of rod. Base fitted with levelling screw and feet.

	a	b	c	d	e
Base Size (cms)	20 x 12.5	22.5 x 15	22.5 x 15	30 x 20	30 x 20
Rod Length (cms)	60	60	75	75	90

Rectangular pressed stainless steel, hole is located centrally on the length.

	a	b
Base Size (cms)	15 x 10	20 x 13
Rod Length (cms)	60	60

Malleable iron, ring and arm of strong circular section, with open boss fitted with thumb- screw to clamp on stands. Distance between center of ring and supporting rod is 12cms. Fits rods upto 13 mm. With the following inside diameters
A: 5.5 cms.
B: 7.5 cms.

For laboratory stand, die pressed of mild steel strip, chrome plated, accept rod up to 18 mm. diameter and clamp rod 7.5 mm diameter which are secured with nickle -plated thumb screws.

For laboratory stand, for use in schools and colleges, die-asted alloy, accepts rods up to 16.5 mm. diameter at right angle to each other which are secured with nickle plated brass Tommy screws.

Made of heavy metal with side rod for insertion in clamp holders. Dimensions are approx.

Capacity 1.7cm approx. , rubber teat, length 40mm, 110mm overall. 

Rings, with plain stem 8-mm. diameter with welded joints for greater strength. Diameter Inside (cm): 5.5, 7.5, 10

Made of sheet metal and chrome plated, spring controlled jaws cork lined which can accept 12 to 50 mm dia., articles with brass wing nut fitted with 15 cm., long mild steel rod.

Two prong, comprises alloy pressure die casting with other parts of plated brass, clamp accepts articles from 15-60mm dia, actuated by nickle plated brass pummles and with twin screws, the jaws are cork lined. fitted with 15Cms. long mild steel or Al. rod.

Die-cast alloy with of plated brass parts. clamp accepts articles from 2-90mm. diameter actuated by nickle plated brass twin screws, The design of the jaws ensures firm grip at all angles of opening and cork lined, complete with 15cm long MS or aluminium rod.

Three prong, die cast in alloy, other parts made of plated brass, clamp accepts articles upto 75mm. diameter, two nickle plated brass screws, and jaws are covered in rubber, fitted with 15Cms long MS. or Al. rod.

Die cast aluminium alloy moulded clamp, spring controlled cork lined or rubber covered jaws with aluminium alloy boss head. Boss head accommodates rods up to 15mm and can rotate with the help of wing nut.
a. Three finger clamp.
b. universal clamp.

For holding flat, conical and round bottom flasks with adjustable chrome plated brass arms.
Capacity: 100, 250, 500, 1000, 2000ml.

same as above but with rubber coated jaws and 28cms long MS. rod of 10cms dia.

With side arm, made of Borosilicate glass. Sizes are approx.

With horizontal side arm bent downwards at 45º, size 150 mm in height and 24 mm in diameter approx.

Graduated or non graduated medium wall, with or without rim, Borosilicate glass. Graduations are clearly marked in white colour.

Wood, with spring steel for closing jaws.
a). length 18 cm, accepts tubes 11-19mm.
b). length 26 cm, accepts tubes 11- 30 mm.

Metal, with sliding collar and wooden handle, accepts tubes 22- 32 mm.

Plated spring steel wire holder with finger grip. The jaws will accept tubes up to 40 mm. diameter and their alignment is maintained by a wire collar. Overall length 16 cm.

Made of stainless steel.
Sizes : (a). 15cms and (b). 20cms

Nickel plated steel, for lifting globules of mercury. Length 20 cms. approx.

For the convenient and safe handling of beaker containing hot solutions and for pouring out the contents.
The jaws are asbestos covered to ensure firm grip. Overall length of tong 30 cms. approx. Made of stainless steel.

As above but jaws silicone covered.

Stainless steel, with asbestos lined rectangular jaws giving an extremely firm grip to flasks of any shape from 100- 2000 ml. capacity. Overall length of tong 30 cms. approx.

Wooden and polished, to hold 12 pipettes horizontally. Height 23 cms. width 26 cms., and depth 12 cms.

Made of seasoned hardwood, polished, with clamping screw. Rods are approx. 460x16 mm. Single base 200x110 mm. Double base 290x110 mm approx.
a) Single
b) Double

Made of seasoned hardwood, polished, with clamping screws. Rod is approx. 460x16 mm.
Base size 290x110 mm. fitted with rubber feet, clamp with lined jaws and funnel holder slotted for ease of entry.

Made of seasoned wood. Can Accept 2 tubes of 25 mm. and 4 tubes of 16 mm. 6 vertical pegs for drying.

Made of seasoned hardwood, polished, with single row of holes. Vertical pegs are provided for quick drying of the test tubes.
a. For Six Test Tubes, with Six pegs, two holes of 32mm. diameter and four holes of 22mm. diameter.
b. For Twelve Test Tubes, with twelve pegs, two holes of 32mm. diameter and ten holes of 22mm. diameter.

Made of aluminium, made from thick 18 gauge aluminium sheet and anodized, fabricated in three tier. For 24 tubes.

To hold single burette. Provided with a positive grip and release. Comprising lightweight but mechanically strong body with brass chrome plated jaws. Rubber covered having spring action which effects positive grip. A single thumbscrew secures the clamp to rod of nominal 13-mm. diameters. The clamp frame surface is finished with gray color.

Same as above, but to hold two burettes.

Made of seasoned hardwood, polished, with plastic clamping screws. Rods are approx. 460 x 16 mm. Single base 200 x 100 mm. Double base 290 x 110 mm.
a. Burette stand, Hardwood, Single. K
b. Burette stands, Hardwood, Double. L

For the visual observation of the migration of coloured ions. Comprises central loading tube with funnel attached to a 'U' tube and two carbon electrodes with screw terminals.
Sizes 19.5cms. height and 6.5cms width.

Conical plain, made of borosilicate glass.
Capacity (ml) : 10, 15, 50

Conical graduated, made of borosilicate glass.
Capacity (ml) : 10, 15, 50

Round bottom with screw cap and Teflon liner.

Solid, superior quality rubber resistance to acid, alkali and ammonia.

Size No.	Top (mm)	Bottom (mm)	Length (mm)
0	13	9	15
1	14	11	18
2	16	13	20
3	19	14	21
4	21	15	22
5	22	17	23
6	24	20	24
7	26	21	27
8	26	21	27
9	28	21	31
10	30	26	33
11	33	30	33
12	34	30	34
13	38	31	37
14	41	32	42
15	43	34	40
16	45	35	36
17	49	40	40
18	53	48	33
19	58	44	45
20	60	51	56

Mixed Pack containing sizes as follows. 8 each No. 2, 3, 4, 5, and 6 nos. each of 7, 9 and 3nos. each of 10, 11. Pack of 50.

Mixed Pack containing sizes as follows. 7 each No. 0, 1, 2, 3, 4, and 3 nos. each of 5, 7, 9, 10, 11. Pack of 50.

Translucent, highly elastic, odorless, suitable for use over a temperature range - 50 to 250ºC. can be sterilized by steam or by hot air.

Size No.	Top (mm)	Bottom (mm)	Length (mm)
9	11	9	20
11	14	11	24
13	16	13	24
15	18	15	24
17	20	17	26
18	21	18	26
19	22	19	28
23	25	23	28
25	28	25	28
27	31	27	32
29	33	29	32
31	36	31	35
33	38	33	38

Nickel plated, made of iron, good quality for schools.

Nickel plated, made of brass, thick quality

Pinch cock, nickel plated iron, flat jaws for compressing flexible tubing

Nickel plated steel, with projection plate to prevent damage to tubing by and of screw, with hinged bottom bar for direct fitting and removed without access to ends of tube. As above, but made of Brass.

Nickel- plated finish. Cutting tube mounted with safety under- flange in shaped handle ensuring a dislodged tube cannot injure that operator.  With iron rod for cleaning borers.
a) Set of 6 size 4 - 10mm
b) Set of 12 size 4 - 18mm
c) Set of 18 size 4 - 27mm

As above, but extra superior quality.
a) Set of 6 size of 4 - 10mm
b) Set of 12 size of 4 - 18mm
c) Set of 18 size of 4 - 27mm.

Plated metal cone with hinged cutter blade set in slot and metal handle. Borer restored to circular shape by cone, edge cut to correct angle by depressing blade using thumb pressure.
For borer diameters 4-27 mm.

For drilling uniform and straight holes in cork or rubber stoppers. Cast - iron frame with wood platform 10 cm. diameter to support work and adjustable guide rod, central hole through wheel spindle for ejector rod and introduction of lubricant (water or methylated spirit).
Complete with set of 12 nickel- plated borers cutting sizes from 7 to 25 mm.

Cast iron, for softening corks evenly, by rolling, without increasing the porosity. To accommodate corks up to 32-mm. diameters. On wooden base.

Mouth, nickel-plated brass, with nipple. Size (cm) : (a) 20 and (b) 30

Made from fine quality compressed charcoal.
Size 25-mm. square sections and 100 mm. Pack of 10 pieces.

For demonstration of the decomposition of water, determination of chemical composition by electrolysis and with applications in the evaluation of the electro chemical equivalent of hydrogen. For the electrolysis of water, platinum electrodes are used and for the electrolysis of ammonia or hydrochloric acid carbon electrodes are used. The electrodes, available separately, are mounted in rubber stopper for insertion into the open ends of the VOLTAMETER limbs. This method, in addition to being convenient, obviates the use of fragile connections, such as platinum wire loops fused through the limbs. The glass unit has two connected limbs, each of approximately 50 ml. capacity, integral with reservoir tube and funnel shaped bulb, with a stopcock at the top of each limb for use on 12Volt D.C. supply.
 a) Voltameter, glass unit only, graduated, each limb 0 to 50x0.2 ml. but without stand.
i) Neutral glass
ii) Borosilicate glass.
b) Metal stand with mounts for giving support to cross limb and vertical limbs for above.
c) Carbon electrodes, in rubber stoppers approx. 110mm. long in protection tube.
d) Pair of platinum electrodes with rubber stopper and protection tube.
e) Power supply 12Volts DC

Supplied in length of 0.5 meter approx. Pack of 30

Neutral glass, light wall, heat and chemical resisting. Supplied in length of 0.5 meter approx. Pack of 30.

Corning glass, light wall, length of 1.5 meter, ±25 mm.

Soda glass. Supplied in length of 0.5 meter approx. Pack of 10.

Dia. 4mm to 10mm.

Borosillicate glass, open both ends. For oxidisation and reduction of chemical substances. Length 30cms.

With short glass tube fused to one end to enable the collection of reacting gases. Suitable for the reduction of metal oxides with hydrogen. Dimension 150 mm. length and 15 mm diameter.

Extra soft quality, conforms to standard specifications, resistant to acids, alkalis. Pack of 10 meters.

Ordinary pressure, extra soft thickness, conforms to standard specifications.

High pressure, extra soft quality, conforms to standard specifications.

Highly elastic, non- toxic, heat resistance from -50ºC to 250ºC repeatedly autoclavable, flexible odorless and transparency of the tubes allows visibility of the flowing fluid.

Seamless, translucent very flexible, suitable for connections to glass. Length 92cms.

Transparent, strong, very flexible, suitable for connections to tape.

Made of glass. Three way T- Shape, Y-Shape, U-Shape, riffled end for rubber tubing, outside diameter 8 mm. Available in polypropylene also.

Made of polypropylene. Three way Y- shape, riffed end for rubber tubing. 8 mm. outside diameter. Available in glass also.

Made of brass, lever handle, spring loaded, locking arrangement to ensure rotation does not go beyond 90 Degree standard 3 mm. bore, inlet 1/4 inches BSP, flange dia. 54 mm. with three screws to fix on bench or any other surface. Designed to operate at pressure upto 2 psi ( 0.14 kg/ cm2 ) suitable for town gas supply or bottled LPG., elegant design, painted with special scratch and chemical resistant paint / chrome plated.
A . One way
B. Two way
C. Three way
D. Four way

Made of brass, chrome finish, inlet tail is threaded 1/2 inch. BSP outlet tube is made out of 15 mm. brass tubing which is coupled to the tap standard by means of a sleeve not allowing the neck to swivel or be locked in a desired position. Leakproof operation, bench mounting.
A. Single way
B. Two way
C. Three way
.

Made of brass, chrome finish, inlet tail is threaded 1/2 inch. BSP leakproof operation, suitable for wall mounting.
A. Two way
B. Three way

NICE- make, for Colleges. Supplied in plastic case of 10 books each with 20 leaves of size 63.5 x 10 mm. wide approx. Total 200 leaves.
Colour : Red and Blue

GEM- make, for Colleges, Universities, extra superior quality. Supplied in box of 5 books each with 20 leaves of size 63.5 x 10mm. wide approx. Total 100 leaves.
Colour : Red and Blue

Best make, for Colleges, Universities. Supplied in box of 5 books each with 20 leaves of size 63.5 x 10 mm. wide approx. Range pH 1 to 10 or 1 to 11. Total 100 leaves.
A. As above but pH range 10-20

Indicator paper supplied in plastic dispenser containing 5 meters of 8mm. wide test strip. A color chart is provided on the side of each dispenser. Full range covering from 1 to 10 pH in step of 1pH.

EKI- make, Cobalt Chloride. Supplied in plastic case of 5 books each with 20 leaves. Total 100 leaves.

Box of ten books of twenty leaves 65x10mm. Color- matching charts are printed on the cover of each book.
Specific Range:
a) 2.0 to 4.5 pH.
b) 3.5 to 6.0 pH.
c) 5.0 to 7.5 pH
d) 6.5 to 9.0 pH
e) 8.0 to 10.5 pH
Wide Range:
f)  2.0 to 10.5 pH
g) Multi Range contains each of above 6 ranges.
Full Range:
h) 1.0 to 14.0 pH.

Size 9 x 14.5 cms. Pack of 100 leaves.

For laboratory, stickers pack of 130, self- adhesive. Size 55 x 30 mm. With name of chemicals and reagents commonly used in laboratory.

Double ended, flat blades.
Length (cms) : (a) 12.5 (b) 15 (c) 20

One end flat and the other end spoon form.
Length (cms): (a) 12.5 (b) 15 (c)20

Double ended, flat blades. Length (cms) : (a) 12.5 (b) 15 (c) 20

With wooden handle. S.S blade.

Total Length is 200 mm. and Outer Dia. of Tube is 15 mm.

With one Bulb. Total Length is 250mm. and Outer Dia. of 17 mm. and of Bulb is 40 mm.

With two Bulbs. Total Length 300mm. and Outer Dia. of Tube 17mm. and of Bulb is 40 mm.

With three Bulbs. Total Length 400mm. Outer Dia. of Tube 17mm. and of Bulb 40 mm.

For the vapour density determination of volatile liquids by measuring the volume of air displayed by a known mass of the substance when vaporized. Comprises 100-ml. bulb with a long vaporizing tube fitted with a side delivery tube incorporati ng a safety rod, designed to support a vapour density bottle and contents before introduction into the tube, by rotating the rod. An outlet jacket surrounds the vaporizing tube. Supplied with vapour density bottle.

As per WHATMAN No. 1. A widely used, general-purpose filter paper. Medium retention and flow rate. Pack of 100 circles.

	A	B	C	D	E	F	G
Diameter (cms)	9	11	12.5	15	18.5	21.5	24

As per  WHATMAN No. 1. Pack of 100 circles.

	A	B	C	D	E	F	G
Diameter (cms)	9	11	12.5	15	18.5	21.5	24

Size 45 x 45 cms. Pack of 500 sheets.

Size 46 x 56 cms. Pack of 500 sheets

With ground in stopper and tabulator Moulded soda glass.

	A	B	C	D	E
Capacity (Liters)	1	2	3	5	10

With outlet for tubing. Moulded borosillicate glass.

	A	B	C	D
Capacity :	250ml	500ml	1 litre	2 litre

With outlet for stopper. Moulded borosillicate glass.

	Capacity(ml)	Approx. O.D. (mm)s	Approx. Height (mm)
A	100	104	200
B	2000	129	265
C	5000	190	320
D	10000	215	410

Media vaccine, narrow mouth with aluminium screw cap and rubber linear.
Capacity (ml) : (A) 7 and (B) 14

Media vaccine, narrow mouth with aluminium screw cap and rubber liner, Capacity 28 ml.

Spherical pattern, light blown corning glass, with flat bottom and perforated stopper.

	a	b	c	d
Capacity (ml)	10	25	50	100

Gas Washing, Dreschsel’s, with interchangeable joint head B- 29, made of borosilicate glass.

	a	b	c
Capacity (ml)	125	250	500

With interchangeable joint.

Ground in stopper.

	a	b	c	d
O.D. x Ht. (mm)	40 x 30	50 x 25	50 x 35	50 x 50
Capacity (ml)	20	20	35	50

Nylon head with fan shaped end, on galvanized wire.

	Head dia. x Length(mm)	Overall Length(mm)
A	120 x 65	600
B	40 x 75	600

Bristle, on galvanized wire. Head size 65 x 40mm. Overall length 230 mm.

Tapered bristle with cotton tip, for tubes 19 to 25 mm. bore. Overall length 230 mm. on galvanized wire.

Bristle head, 150 mm long x 70-mm. diameters on hardwood handle. Overall length 400 mm.

Bristle head on wire with wooden handle.

	Head Length x Dia(mm)	Overall Length(mm)	For Bottle Size(ml)
A	65 x 45	300	125
B	75 x 50	350	250
C	100 x 65	400	500
D	150 x 75	750	1000

Nylon head on wire with wooden handle.

	Head Length x Dia(mm)	Overall Length(mm)	For Bottle Size(ml)
A	65 x 45	300	125
B	75 x 50	350	250
C	100 x 65	400	500
D	150 x 75	750	1000

Bristle head on wire with wooden handle.

	Diameter(mm)	Length(mm)	Burette(ml)
A	13	500	10
B	16	600	25
C	19	750	50
D	25	900	100

Conical shape, soda glass, long stem.

	A	B	C	D	E
Diameter (cms) :	56.2	57.5	10	12.5	15

Conical shape, soda glass, short stem.

	A	B	C	D	E	F
Diameter (cms)	5	6.25	7.5	10	12.5	15

Plain, 60 Degree angle, long stem, made of borosilicate glass.

	A	B	C	D
Diameter (cms)	5	6.5	7.5	10

Short stem, made of Polypropylene.

	A	B	C	D
Diameter (cms)	12.5	15	20	25

Buchner, with straight sides above the perforated plate.

	A	B	C	D	E	F	G	H	I	J
Diameter (cms)	3.5	5	6	7.5	10	12.5	15	20	25	30

Sintered glass, with flat sintered glass plate.< td>J

	A	B	C	D	E	F	G	H	I	K
Porosity	1	2	3	1	2	3	4	1	2	3	4
Capacity (ml)	35	35	35	80	80	80	80	125	125	125	125
Plate Dia (mm)	30	30	30	40	40	40	80	65	65	65	65

Sintered glass, with flat sintered glass plate.

	A	B	C	D
Porosity	1	2	3	4
Capacity (ml)	20	20	20	20
Plate Dia (mm)	20	20	20	20

Cylindrical, with stopcock and interchangeable ground glass/plastic stopper, graduated, Borosilicate glass.

	A	B	C	D
Capacity (ml)	50	100	250	500

Made of Borosilicate glass, with permanent stained graduation. Colour-coded. Zero at jet.
Cap. x Graduation(ml) : A) 1 x 0.01 (B) 2 x 0.02 (C) 5 x 0.05 (D) 10 x 0.10 (E) 25x 0.20

Calibrated for delivery to jet. Last drop expelled by blowing, permanent amber
graduation. Colour Coded.
Capacity x Graduation(ml) :

(a) 0.1 x 0.01	(e) 2.0 x 0.02
(b) 0.2 x 0.02	(f) 5.0 x 0.1
(c) 0.5 x 0.05	(g) 10.0 x 0.1
(d) 1.0 x 0.01	(h) 25.0 x 0.1

Disposable, Pasteur type, soda glass, without teat, in pack of 250.
Length (mm) : a)145 and (b)230

Made of Borosilicate glass, permanent amber graduation. Capacity 10.75 ml.

Capacity 1.7 ml, approx., rubber teat, length 40 mm, 110 mm, overall. Pack of 10.
a) Narrow Mouth
b) Wide Mouth

Glass body, length 12.5 cm, supplied with rubber teat. Useful for dispensing liquid from test tubes. Pack of 5.

Made of neutral glass, bulb form, single graduation on upper.Stem, permanent graduation.

	A	B	C	D	E	F	G	H
Capacity (ml) :	2	5	10	15	20	25	50	100

Made of Borosilicate glass, bulb form, single graduation on upper stem, permanent amber stained graduation. Colour-coded.

	A	B	C	D	E	F	G	H
Capacity (ml) :	2	5	10	15	20	25	50	100

Above pipettes with class-a accuracy are available.

Borosilicate glass, with permanent stained graduation. Color-coded. Zero at top.

	Capacity x Graduation (ml)
A	1 x 0.01
B	2 x 0.02
C	5 x 0.05
D	10 x 0.01
E	25 x 0.20

Rubber, pear shaped, for use with pipettes.

	A	B	C	D	E	F
Capacity (ml) :	5	10	15	25	50	100

Bulb for pipetting noxious solutions, microbial suspensions and other harmful or unpleasant solutions. Comprise a bulb and three pinch valves controlling influx of pipette contents. Bulb diameter is 54 mm.
Colour : (A) Red  (B) Black  (C) Grey

A range of economic, accurate, fixed volume micro-pipettes. Models 2 mol 1000 ml They are fully autoclavable to 12º C.

	A	B	C	D	E	F	G	H	I	J	K	L	M
Capacity (ml) :	2	5	10	20	25	50	100	200	250	300	400	500	1000

An economic, accurate, complete with rechargeable battery. Pipette adapter.

Simple pipette filler for use with bulb and cylindrical pipettes up to 25 cm. Easy to use with finely adjustable thumb wheel, no possibility of sucking back. Ideal for bromine, acids and alkalis.
Capacity (ml) : (a) 10 and (b) 25

A range of economic, accurate. Variable volume micro- pipettes. Models 0.5 up to 5000ml They are fully autoclavable to 121ºC.

	A	B	C	D	E	F	G
Capacity (ml) :	0.5-2	1-10	2-20	10-100	20-200	200-1000	1000-5000

Glass dropper with Teat in different sizes. plain and graduated.

Knitted seamless to provide maximum work comfort and efficiency in all seasons. Neutral color, bleached white, regular size.

For handling noxious material. Medium gloves for light duty, acid and alkali proof.

Size (per pair) :

a) 10"

b) 12"

c) 14"

General purpose, medium weight gloves for light duty, acid and alkali proof.

Made of white drill/white polyester. Modern styling with concealed buttons, back vent and three large pockets. Length 100 cms.
Chest (cms) : (a) 96 and (b) 108

Plastic, for eye protection. Can be used over normal spectacles.
A) With normal glasses.
B) As above but with dark glasses.

Low form, with spout, made of soda glass, can be used up to 100ºC.< td>j

	a	b	c	d	e	f	g	h	i
Capacity (ml)	25	50	100	150	250	400	500	600	800	1000

Tall form, with spout made of borosilicate glass.

	a	b	c	d	e	f	g	h	i	j	k	l	m
Capacity (ml)	5	10	25	50	100	150	250	400	500	600	1000	2000	3000

All Beakers offered are of nominal capacity and graduation mark showing approximate capacities can be supplied at an extra cost. Beakers made of borosilicate glass are equivalent to Pyrex/Corning in quality and durability.< td>j

	a	b	c	d	e	f	g	h	i
Capacity (ml)	25	50	100	150	250	400	500	600	800	1000

Round bottom, short neck, wide mouth, made of soda glass.

	a	b	c	d	e
Capacity (ml)	100	150	250	500	1000

Round bottom, long neck, made of soda glass.

	a	b	c	d
Capacity (ml)	100	150	250	500

Round bottom, long neck, made of borosilicate glass, interchangeable joint.

	A	B	C	D	E	F
Capacity (ml)	50	100	250	500	1000	2000
Interchangeable	19/26< /td>	24/29	24/29	24/29	24/29	24/29
Height (mm)	95	120	140	160	188	228

Pear shaped, short neck, made of borosilicate glass, with interchangeable joint.

	A	B
Capacity (ml)	25	50
Interchangeable	14/23	14/23

Long neck, made of soda glass, vial mouth.

	A	B	C	D	E
Capacity (ml)	100	150	250	500	1000

Florence, flat bottom, made of borosilicate glass.< td>J

	A	B	C	D	E	F	G	H	I	K
Capacity (ml)	25	50	100	150	250	300	500	1000	2000	3000	5000

Flat Bottom, short neck, made of borosilicate glass, interchangeable joint.

	A	B	C
Capacity (ml)	150	250	500
Interchangeable	24/29	24/29	24/29
Height (mm)	115	130	148

One center neck and one parallel side neck
Capacity: 250ml to 20000ml

One center neck and one angular side neck
Capacity: 100ml to 20000ml

All necks parallel. Capacity: 250ml to 20000ml

One center neck and two angular side necks. Capacity: 100ml to 20000ml

Round bottom flask with four necks.
Capacity: 500ml to 20000ml
Size of the centre socket, side sockets (angular or parallel) on demand

Rubber for use with dropper pipettes.

	A	B	C
Capacity	Small	Medium	Lar ge

Made of neutral glass, with Mohr clip, glass jet and rubber using.

	A	B
Capacity :	25 x 0.1	50 x 0.1

Made of neutral glass, with single bore glass stopcock.

	A	B
Capacity :	25 x 0.1	50 x 0.1

Made of borosillicate glass, with single bore glass stopcock. Conforms to BS 846.

	A	B
Capacity :	25 x 0.1	50 x 0.1

Made of borosillicate glass, with single bore Rotaflow stopcock. Conforms to BS 846.

Made of borosillicate glass, with single bore PTFE KEY, screw type.

	A	B
Capacity :	25 x 0.1	50 x 0.1

borosillicate glass, with internal filling tube and automatic zero. Fitted with Rotaflow stopcock.

	Capacity (ml)	Graduation	Tolerance (ml)
A	100	.10	.1
B	250	.10	.1
C	500	.10	.1

These flasks are blown specially for iodine value determination. The stopper handle projects above liquid seat trough to facilitate its removal, with interchangeable stopper.

	A	B	C
Capacity (ml)	100	250	500
Interchangeable	24/29	24/29	24/29

Long neck, round bottom, borosilicate glass. These flasks specially styled for nitrogen determination as per KJELDHAL method are provided with tooled necks for extra strength and stopper fit.

	A	B	C	D	E	F
Capacity (ml) :	10	30	100	300	500	800

As per Srl. No. 6192 but with interchangeable joint.

	A	B
Capacity (ml)	500	800
Interchangeable	24/29	24/29

With interchangeable plastic stopper. Accuracy as per Class-B of IS 915: 1975. Made of borosilicate glass.Capacity (ml)

	A	B	C	D	E	F	G	H
25	50	100	200	250	500	1000	2000
Interch angeable	10/15	10/15	14/15	14/15	14/15	19/20	19/20	24/25

With interchangeable glass stopper. Accuracy as per Class-B of Is 915: 1975. Made of borosilicate glass.< td>J

	A	B	C	D	E	F	G	H	I
Capacity (ml)	5	10	25	50	100	200	250	500	1000	2000
Interchangeable	10/15	10/15	10/15	10/15	10/15	14/15	14/ 15	19/20	19/20	24/25

Flanges, wide mouth, OD 150mm, ID 100mm.

Flat flange, inter-changeable joint OD 150mm, ID 100mm.

Flat flange joint 100mm.

Round bottom, with side arm, borosilicate glass.

	A	B	C	D	E
Capacity (ml) :	100	250	500	1000	2000

Erlenmeyer, narrow neck, made of soda glass.

	A	B	C	D	E	F
Capacity (ml) :	50	100	150	250	500	1000

As per Srl. No. 6183 but graduated. Graduation marks approximate.

	A	B	C	D	E	F
Capacity (ml) :	50	100	150	250	500	1000

Erlenmeyer, narrow mouth, made of borosilicate glass.Capacity (ml) :

	A	B	C	D	E	F	G	H
10	25	50	100	150	250	500	1000

Erlenmeyer. wide mouth but graduated. Graduation marks approximate.

Erlenmeyer,  Graduation marks approximate.

	A	B	C	D	E	F	G	H
Capacity (ml) :	10	25	50	100	150	250	500	1000

Erlenmeyer, narrow mouth, made of borosilicate glass, with interchangeable stopper.

	A	B	C	D	E
Capacity (ml)	25	50	100	250	500
Interchangeable	14/23	19/26	24/29	29/32	29/32